YTX300H/YTX300

ISM TransceiverModule With +20dBm(100mW) Output Power

(The purpose of this YTX300H/YTX300 SPECcovers mainly for the hardware and RFparameterinfo of the module,For software infoplease refer toYX300 chip datasheets anddemo program of YTXDuino (rm) Develo -pmentKit)
1. General introduction
YTX 300H/YTX300module series’ design is based on thehigh performanceCMOSTEK NextGenRF TM YTX300chip, ltoperate at 433/868/915MHz ISM band , The lowreceive sensitivity(-120dBm)coupled with +20dBm(YTX300H)/+13dBm(YTX300)output power ensuresextended range and improved link performance.

2. Features:
140dB maximum link budget.
Low RX current of 7mA.
+20 dBm output power @YTX300H;+13 dBm output power @YTX300Programmable bit rate up to 300 kbps@FSK/40 kbps@OOK
High sensitivity: down to -120dBm.
FSK, GFSK, and OOK modulation.
SMD Package (16x16X1.8
3.Application:
Meter Reading
Wireless data collection
Home automation and

Pin Definition：

1. YTX300H Pin Definition

    

   

    

   FFiigure 1. YTX300H Pin Definition

    

    

   Number	Definition	Type	Function
   1	ANT	AI/ AO	RF signal input/output.
   2	GND	G	Ground.
   3	TX-ANT	I/O	Tx Antenna sseelect iinnppuutt ppiinn, When YTX300H is TX state,TX_ANT should be = 0, RX_ANT should be =1
   4	RX-ANT	I/O	Rx Antenna select input pin, When YTX300 IS RX state,RX_ANT should be = 0, TX_ANT should be = 1
   5	3.3V(VDD)	PI	Power supply input,1.8-3.6V.
   6	GPIO1	I/O	General Purpose Digital I/O that may be configured through the registers to perform variousfunctions
   7	GPIO2
   8	GPIO3
   9	GND	G	Ground.
   10	SDIO	I/O	SPI Data input and output.
   11	CSB	I	SPI Chip select input, active low.
   12	SCK	I	SPI Clock input.
   13	FCSB	I	SPI FIFO select input, active low.
   14	NC		No Connect.
   15	NC		No Connect.
   16	GND	G	Ground.

   YTX300 Pin Definition

    

   

    

   Figure 2. YTX300 Pin Definition

    

   Number	Definition	Type	Function
   1	ANT	AI/ AO	RF signal input/output.
   2	3.3V(VDD)	PI	Power supply input,1.8-3.6V.
   3	GND	G	Ground.
   4	NC		No Connect.
   5	CSB	I	SPI Chip select input, active low.
   6	SCK	I	SPI Clock input.
   7	FCSB	I	SPI FIFO select input, active low.
   8	SDIO	I/O	SPI Data input and output.
   9	GPIO1	I/O	General Purpose Digital I/O that may be configured through the registers to perform variousfunctions
   10	GPIO3
   11	GPIO2
   12	NC		No Connect.
   13	NC		No Connect.
   14	GND	G	Ground.

    

   Electrical ：

   Maximum

   parameter	minimum		Unit
   Positive Power Supply	-0.3		V
   Voltage O	-0.3	+ 0.3	V
   Voltage On Analog Inputs	-0.3	+ 0.3	V
   RX Input Power	-		d℃Bm
   Storage Temperature	-55	+ 25	℃
   Soldering Temperature(10s)	-	+ 55
   	-2		KV

    

   parameter	minimum		Unit
   Positive Power Supply	+1.8		V℃
   Working Temperature	-40
   Supply Voltage Slew Rate	1	-	mV/us

    

   DC characteristic

   parameter	conditions	minimum		maximum	Unit
   YTX300H	433MHz band, Pout =+20dBm	-	75	100	mA
   TX WorkingCurrent	868MHz band, Pout =+20dBm	-	80	100
   	915MHz band, Pout =+20dBm	-	85	100
   YTX300	433MHz band, Pout =+13dBm	-	28	45	mA
   TX WorkingCurrent	868MHz band, Pout =+13dBm	-	30	45
   	915MHz band, Pout =+13dBm	-	30	45
   YTX300H/YTX300	433MHz band,	-	7	10	mA
   RX WorkingCurrent	868MHz band,	-	7.5	10.5
   	915MHz band,	-	7.5	10.5
   YTX300H/YTX300 Sleep Current	All band	-	-	1	uA

    

    

   parameter	conditions	minimum	typical	maximum	Unit
   TX Frequency Range Programmable	433 MHz band, 868 MHz band, 915 MHz band,	413 848 895	- - -	453 888 935	MHz
   YTX300H Output Power	433/868/915MHz band	-	+20	-	dBm
   YTX300 Output Power	433/868/915MHz band	-	+13	-	dBm
   Symbol Rate, FSK Mode	Programmable	0.1	-	300	kbps
   SymbolRate, OOK Mode	Programmable	0.1	-	40	kbps
   Frequency Deviation,FSK	Programmable	1	-	200	KHz
   Frequency Resolution		-	24.8	-	Hz

    

   parameter	conditions	minimum	typical	maximum	Unit
   RX Frequence Range	433 MHz band,	413	-	453	MHz
   Programmable	868 MHz band,	848	-	888
   	915 MHz band,	895	-	935
   RX Sensitivity	433MHz	-	-120	-	dBm
   OOK ModeSR =1.2 kbps,	868MHz	-	-118	-
   	915MHz	-	-118	-
   RX Sensitivity	433MHz	-	-118	-	dBm
   FSK ModeFDEV = 19.2 kHz, S	868MHz	-	-116	-
   =1.2 kbps,	915MHz	-	-116	-
   Receiver Bandwidth		50		500	KHz
   Blocking Immunity	+/-1MHz offset	-	52	-	dB
   	+/-2MHz offset	-	74	-
   	+/-10MHz offset	-	75	-
   Image Rejection Ratio	IF=280KHz	-	35	-	dB

1. Typical A ：

Figure 3. YTX300HApplication

Figure 4. YTX300 Application

(Foorr software info please refer toYTX300 chip datasheets and demo program of

YTXDuinoTM Development Kit)

7.（All units in mm）

8.